Cisco 300-610 DCID Exam Questions Instant Access

Question 1

A customer needs to deploy a three-tier network architecture that will consist of web, and other business-critical applications. The solution will include Cisco UCS 6324 Fabric interconnects managing B and C Series servers The Fabric interconnects will be connected to the cisco nexus 7706 series switch for network access. A storage array will be directly connected to the UCS deployment. Which type must be used to meet these requirements?

AUCS Interconnect in Ethernet end-host mode
UCS Interconnect in Fibre Channel switching mode
Fabric Interconnects uplinked to the Nexus device using an LACP port-channel in active mode

BUCS Interconnect in Ethernet switching mode
UCS interconnect to Fibre Channel switching mode
Fabric Interconnect uplinked to the Nexus device using an LACP port-channel in passive mode

CUCS Interconnect in Ethernet end-host mode
UCS Interconnect in Fibre Channel end-host mode
Fabric Interconnect uplinked to me Nexus device using an LACP port-channel in passive mode

DUCS Inter conned in Ethernet switching mode
UCS interconnect in Fibre Channel end-host mode
Fabric Interconnects uplinked to the Nexus device using an LACP port-channel in active mode

Answer : A

FC must be in switching mode for Direct Attached Storage.

Question 2

Refer to the exhibit.

A Cisco engineer is configuring Cisco Nexus 7000 Series Switches To simplify initial configuration verification and vPC+/HSRP troubleshooting, the engineer configures the primary vPC+ peer device with the FHRP active router highest priority The primary FHRP device responds to ARP requests, even though the secondary vPC+ device also forwards the data traffic Which configuration enables the Layer 3 connectivity from each vPC+ peer device?

ASet a restore timer that delays the vPC+ restart

BConfigure a VLAN network interface for the same VLAN from both devices

CManually configure virtual MAC addresses for any FHRP protocol

DEnsure that the enhanced Layer 2 license has been installed.

Answer : B

Question 3

An engineer must integrate Layer 4 to Layer 7 services within Cisco ACI Fabric. The main requirement is to have a single point of configuration for network elements and firewall policies.

Which action meets these requirements?

ADefine the service graph model as network policy mode.

BDeploy the firewalls in routed mode with PBR.

CDeploy the firewalls in transparent mode.

DDefine the service graph model as service policy mode.

Answer : D

Question 4

A Cisco UCS chassis with several blade servers, a pair of IOMs, and a pair of Cisco UCS Fabric Interconnects are installed in a data center.

Which two high-availability architectures are recommended between the IOMs and fabric interconnects? (Choose two.)

AOne, two, four and eight links are supported to be used between each IOM and fabric interconnect.

BIOM is connected to the fabric interconnect that is acting as fabric A. and IOM B is connected to the fabric interconnect that is acting as fabric B.

CAny combination of one to eight links are supported to be used between each IOM and fabric interconnect.

DThe lOMs are connected with multiple straight and cross-connect links toward a pair of nonclustered fabric interconnects.

EStraight and cross-connect links should be used between the lOMs and fabric interconnects to offer higher availability.

Answer : A, B

Question 5

Which two types of service profile templates does Cisco UCS support? (Choose two.)

Ainitial

Bpermanent

Cupdating

Dtemporary

Econnected

Answer : A, C

Question 6

What is the disadvantage of asynchronous storage replication as compared to synchronous storage replication in a disaster recovery design?

Areduction in application performance

Bdistance limitations

Cspecific backup requirements

Dpotential data loss

Answer : D

Question 7

An engineer is implementing a storage area network where an NPV is used. The engineer notices that the servers in a storage farm are experiencing heavy traffic contention. The engineer needs to migrate traffic from heavily loaded server interfaces to interfaces with less load. When the new links are deployed, the existing traffic is not rebalanced as expected. Which feature must be used to meet these requirements?

ANPIV

Bmultiple VSAN support

CDVM

Ddisruptive load balancing

Answer : A

Cisco Designing Cisco Data Center Infrastructure 300-610 DCID Exam Questions