Dell EMC D-NWG-FN-23 Exam Questions Instant Access

Question 1

Refer to the exhibit.

Which configuration will allow S1 to ping S2's Lo0 address?

AS1(config-router)# ip route 144.254.32.1 192.168.32.2/32

BS1(config-router)# ip route 192.168.32.2 144.254.32.1/32

CS1(config)# ip route 144.254.32.1/32 192.168.32.2

DS1(config)# ip route 192.168.32.2 144.254.32.1/32

Answer : C

Question 2

Refer to the exhibit.

The output shown is from which command?

AS3(config-router-ospf-1)# show ip ospf database

BS3(config-router-ospf-1)# show ip ospf topology

CS3(config-router-ospf-1)# show ip ospf lsa

DS3(config-router-ospf-1)# show ip ospf statistics

Answer : A

Question 3

A network administrator is designing a Layer 2 topology and requires separate spanning-tree roots to avoid having a given port blocked for all instances. Which spanning-tree protocols will meet this need?

ASTP & RSTP

BRSTP-PV & MSTP

CSTP & RSTP-PV

DRSTP & MSTP

Answer : B

Question 4

To which IEEE standard are dynamic LAGs compliant on Dell EMC Networking OS10 switches?

A802.3af

B802.3ad

C802.3ac

D802.3ae

Answer : B

Question 5

Which commands are required to properly configure an OS10 switch to run OSPF on eth1/1/3 and to add network 144.254.1.0/30 to OSPF area 0?

AOS10(config)# interface ethernet 1/1/3 OS10(conf-if-eth1/1/3)# no shutdown OS10(conf-if-eth1/1/3)# no switchport
OS10(conf-if-eth1/1/3)# ip address 144.254.1.2/30 OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0
OS10(config)# router ospf1

BOS10(config)# router ospf 1
OS10(config-router-ospf-1)# router-id 1.1.1.1 OS10(config)# interface ethernet 1/1/3 OS10(conf-if-eth1/1/3)# no shutdown OS10(conf-if-eth1/1/3)# no switchport OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0

COS10(config)# interface ethernet 1/1/3 OS10(conf-if-eth1/1/3)# no shutdown
OS10(conf-if-eth1/1/3)# ip address 144.254.1.2/30 OS10(conf-if-eth1/1/3)# no switchport
OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0 OS10(config)# router ospf 1

DOS10(config)# interface ethernet 1/1/3 OS10(conf-if-eth1/1/3)# no shutdown
OS10(conf-if-eth1/1/3)# ip address 144.254.1.2/30 OS10(conf-if-eth1/1/3)# no switchport
OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0 OS10(conf-if-eth1/1/3)# router ospf 1

Answer : C

Question 6

Which command shows whether a LAG protocol is static or dynamic on a Dell EMC Networking OS10 switch?

Ashow lacp neighbor

Bshow running-configuration lacp

Cshow interface port-channel summary

Dshow port-channel summary

Answer : D

Question 7

There is a spanning tree mismatch at the global level. PVST+ is configured on a VLT peer. All VLT port channels go down on both VLT peers. A syslog error message is generated. What is the correct action to resolve the issue?

AVerify the VLT LAG ID is configured correctly on both VLT peers.

BEnable RSTP on both VLT peers.

CUse the show VLT detail and show VLT brief commands to view the VLT port channel status information.

DPerform a mismatch check after the VLT peer is established.

Answer : D

Dell EMC Dell Networking Foundations 2023 D-NWG-FN-23 Exam Questions