HP HPE6-A75 Exam Questions Instant Access

Question 1

Refer to the exhibit.

A company has attempted to implement OSPF without success. The devices in Area I need to be able to reach Area 2. Routes should be aggregated for advertisement in other areas. What must be changed to meet these requirements?

AChange Area 3 to Area 0; remove Area 1 from Switch-2 and Area 2 from Switch-1.

BAdd the 10.2.0.0/16 range on Swttch-1 and the 10.1.0.0/16 range on Switch-2.

CAdd Area 1 and Area 2 on VIAN 100 on both Switch-1 and Switch-2. Remove Area 3.

DMove the 10.1.0.0/16 range to Area 2 on Switch-1 and the 10.2.0.0/16rangetoArea 1 onSwitch-2.

Answer : A

Question 2

Refer to the exhibit.

A known unicast packet is received from Switch-1 on the standby and must be forwarded to Switch-2. How does the VSF fabric decide which port in the aggregated (ink should forward the packet?

AThe standby uses its own port in the link aggregation to forward the fabric.

BThe standby sends the packet to the commander over a VSF link, and the commander decides the correct port.

CThe standby uses the typical load sharing algorithm, and it might select either its port or the commander's port.

DThe standby selects the port on the designated forwarder for the aggregation.

Answer : A

Question 3

Refer to the exhibit.

Traffic between the servers m Area l takes a less optimal path rather than the link associated with VLAN l OOO, subnet 10.0.0.0/30. Based on the exhibits, why is this the case?

AThe metric on the VLAN 1000 interface is too low.

BSwitch-1 and Switch-2 cannot achieve adjacency on VLAN 1000 due to mismatches.

COSPF routing switches choose the best intra-area routes based on Area 1 links only.

DThe link between Switch-1 and Switch-2 has gone down.

Answer : C

Question 4

Which technologies can prevent split brain in a VSF fabric that includes Aruba 2930F switches?

AARP MAD or OOBM MAD

BVLAN MAD or ARP MAD

COOBM MAD or LLDP MAD

DLLDP MAD or VLAN MAD

Answer : D

Question 5

An administrator configures the MultiZone feature for a company network, where a mobility cluster is the primary zone and a standalone controller in the company's DMZ represents a secondary data zone. The administrator configures two AP Groups and respective VAPs for the zones on the Mobility Master (MM) in the primary zone. When the APs boot up and establish connections to both zones, the administrator notices that no data connections are established to the data zone.

What must the administrator do to fix this problem?

AConfigure the same AP Groups and VAPs on the standalone controller, and associate the MultiZone APs to both groups.

BConfigure the same AP Group in the data zone as it is in the primary zone, and configure the VAPs in the data zone.

CHave the MultiZone APs initially boot from the standalone controller in the data zone.

DCreate different AP groups and VAPs on the Mobility Master and standalone controllers, and associate the MultiZone APs to both groups.

Answer : D

Question 6

Refer to the exhibit.

A network administrator sets up 802.1X authentication to a RADIUS server on an AOS-Switch. The RADIUS server and user devices are both set up to use REAP MSCHAPv2. The administrator tests the authentication and sees the output shown in the exhibit. Which issue could cause this output?

AThe RADIUS shared secret does not match on the switch and the server.

BThe administrator entered the wrong password for the test account.

CThe switch does not have a certificate tor port-access installed on the switch.

DThe switch port is set for user mode 801. IX. but the RADIUS server is set for port mode.

Answer : A

Question 7

Refer to the exhibit.

An Enforcement Profile has been created in the Policy Manager as shown. Which action will ClearPass take based on this Enforcement Profile?

AClearPass will count down 600 seconds and send a RADIUS CoA message to the user to end the user's session after this time is up.

BClearPass will send the Session-Timeout attribute in the RADIUS Access-Accept packet to the NAD and the NAD will end the user's session after 600 seconds.

CClearPass will count down 600 seconds and send a RADIUS CoA message to the NAD to end the user's session after this time is up.

DClearPass will send the Session-Timeout attribute in the RADIUS Access-Request packet to the NAD and the NAD will end the user's session after 600 seconds.

EClearPass will send the Session-Timeout attribute in the RADIUS Access-Accept packet to the User and the user's session will be terminated after 600 seconds.

Answer : B

HP Aruba Certified Edge Professional HPE6-A75 Exam Questions