NetApp NS0-592 Exam Practice Test Instant Access

Question 1

Your customer has initiated several volume move commands to redistribute the workload in their 8-node cluster. To verify that this process is not affecting their client access, they were monitoring the network switches that provide client access, but they do not see the network load of the volume move command.

In this scenario, what is the reason for the behavior?

AThe volume move command uses the HA iWarp interconnect, not the client access switches.

BThe volume move command uses copy offload protocol, so it does not show up when monitored.

CThe volume move command uses the intercluster LIFs, not the data LIFs.

DThe volume move command uses the cluster interconnect switches, not the client access switches.

Answer : B

Question 2

Your customer states that the storage efficiency on their FAS 8200 is far below what they had expected for a VMware NFS datastore. They enabled deduplication three days ago. The job ran every night for only 10-20 minutes, and the space savings now is less than 5%.

What is causing the space savings to be so low?

AThey have enabled aggregate-level inline data compaction, so the savings are at the aggregate level.

BThey have enabled aggregate-level inline deduplication, so the savings are at the aggregate level.

CThey have not enabled volume-level compression.

DThey have not run a baseline deduplication to scan old data.

Answer : C

Question 3

A customer reports that OnCommand Performance Manager shows that the workload on node-02 in a 4-node cluster has increased to a level that is higher than the threshold. The customer wants to avoid this issue becoming a performance problem.

Which two actions would result in achieving this goal? (Choose two.)

AUse the volume move command to move one or more volumes to another aggregate that is owned by another node that is less utilized.

BUse the storage aggregate relocation command to offload an aggregate to its partner.

CUse the storage aggregate scrub command to verify the parity on the busy aggregates.

DPhysically move the shelf to another node that is less utilized.

Answer : A, D

Question 4

Click the exhibit button.

A customer is reporting that numbers in the statistics volume show command output appear to be incorrect.

Referring to the exhibit, which statement is correct?

AThe problem is due to a difference in operation size.

BPerfstat should be used to explain the behavior.

CThere are operation types that are not listed in the output.

DA case with NetApp should be raised to find the root cause.

Answer : A

Question 5

A reboot was performed by a watchdog reset on the node.

In this scenario, which statement is true?

AThe service processor no longer responds.

BIn case of an L1 watchdog event, determine whether a panic message was recorded.

CIn case of an L2 watchdog event, determine whether a core was dumped.

DThe wafl_check command should be executed.

Answer : A

Question 6

Click the exhibit button.

A customer has an FC SAN with brocade switches. Each server attached to the SAN gas four FC ports. The customer describes that one of their servers has only four paths to the LUNs configured on the cluster. There should be eight paths on all the other servers. The switch administrator has verified the zone configuration.

Referring to the exhibit, which two actions would you perform to troubleshoot the problem? (Choose two.)

AReview the LIF configuration on the cluster.

BReview the driver version on the server.

CReview that the host side FC link ports are enabled.

DReview the igroup configuration on the cluster.

Answer : A, B

Question 7

Click the exhibit button.

Your customer added a new DS4246 shelf to their FAS system. They created an aggregate on the new shelf. Two weeks later, they log in to Active IQ and discover the Medium Impact error shown below.

''Both SAS connections from one controller go to the same shelf.''

Referring to the exhibit, which statement is correct?

AYou are unable to obtain a ''Cable Visualization'' overview from Active IQ.

BA faulty cable is causing the problem.

CA faulty IOM is causing the problem.

DYou can correct this problem without downtime on the FAS system.

Answer : D

NetApp Certified Support Engineer - ONTAP Specialist NS0-592 Exam Practice Test